| ||||||||||||||||||||
 | ||||||||||||||||||||
|
||||||||||||||||||||
Not to mention, some men happen to think that the Dewalt DW723 Miter Saw and the power tool stand are the best creation of man ever since beer was invented! A power tool like the Dewalt DW723 needs a sturdy stand that is versatile, stable and complete. If you're looking for a power tool like a drill that will fit into little nooks and crannies, let us tell you that the Panasonic 15.6 Volt drill/driver has been receiving rave reviews from the consumers. The batteries for this power tool can last a remarkably long time. The motor for this power tool is so versatile that it packs up to 390 inch-pounds of torque. It's hard to find another power tool to match that, frankly speaking. Speaking of drilling, for power tools addicts, you've just got to get the Paslode 900420X IM350-CT Impulse Cordless Framing Nailer. The Contractor's Performance Pack comes with extra batteries, tools for charging the nailer in your car, 2 fuel cells, lube oil, degreaser cleaner and safety goggles too. This power tool pack is truly going to make your experience a very convenient one. Setting the power tool up is a no brainer and on top of that, this powerful power tool is extremely light – weighing in at only 6.9 lbs. This power tool has an indicator light so that you'll know when the battery is running low. The cycle rate rate is about 2 to 3 nails per second. Top performance power tool! With the Constructor's Performance Pack, you don't have to worry about running out of power because you can charge the power tool's battery up and when one battery runs out, you can just stick the extra battery into the power tool and just keep on going. For power tool lovers, you?ll also love the Makita 6347DQDE 18-Volt Cordless Driver-Drill kit. This power tool kit comes is a 2-speed driller that is as versatile as it comes. This power tool comes with 2-batteries (no extra charge), Phillips/slotted bit, charger and an Pack-and-Carry case. This power tool comes with 2 18- Volt Ni-MH batteries, therefore, you can expect a longer run time with this power tool. This power tool also comes with Industrial ½' keyless chuck with easy replacement of brushes. Have fun with your power tools! Barry Shultz is the author of Atlascopy News, and President of Atlascopy, Inc. Atlascopy specialized in affordable alternatives to the high cost of printer supplies. Sign up for the Atlascopy Newsletter and get 10% coupons every week in your email. http:/ 1333 Ever wanted to know how the big boys make remanufactured inkjet cartridges? Read on and I'll give you a quick outline of what you actually get when you buy a remanufactured inkjet cartridge. The first thing to realize is that refillers, or Remanufacturers only remanufacture inkjet cartridges that contain a print head. Those include Hewlett Packard and Lexmark. All the others are variations of the aforementioned cartridges. This is because the generic or compatible cartridges for the others, Canon, Epson etc., are very cheap and they could not make a profit by remanufacturing them. Step 1. The Empties Search. In order to remanufacture an inkjet cartridge you must first have the empty one to refill. When a new printer using a new cartridge is introduced it may take several months if not years for the empty cartridges to become available in the quantity that warrants the refiller to make the investment to tool up for remanufacture. As of this date a very popular HP cartridge that was on the market for over a year is still very scarce as remanufactured. A very popular Lexmark cartridge, the 12A1970 cartridge is almost impossible to locate because Lexmark is buying them back, but these are articles unto themselves. The inkjet cartridge remanufacturer carefully inspects the cartridges for blemishes and for evidence that is has been previously refilled. They must be virgin cartridges (never refilled) or they won't get refilled. (By most scrupulous remanufactures) Next the cartridges are electrically tested using sophisticated electronic equipment that tests the print heads and related electronics. This will be a 100% pass/fail test. No in betweens here. Anything under 100% gets tossed. Step 2. Cleaning. Each cartridge is cleaned ultrasonically inside and out. All remaining ink is thoroughly flushed from the cartridge and they are bathed in a cleaning solvent. Step 3. Refilling. Here is where to pros are separated from the hobbyist. To properly refill a cartridge there must be a measurable balance between ink flow, vacuum and pressure. Very expensive refilling machines are needed to accomplish this task properly. The machine will have the capacity to refill many cartridges at the same time. The cartridges get snapped in place and when all the gizmos are set properly they all get filled at the same time. Step 4. Resealing. After the cartridges are filled with ink, certain ones must be resealed. Clever techniques are used here so you can't tell that is was refilled. I can show you but then I'd have to..... well you get the picture. Step 5. Testing. This stage requires several tests and refillers will not always take them in the same order so I'll just tell you the ones I know about. Print tests are done by either using a regular inkjet printer designed to use that cartridge. A test pattern of some sort will gauge the quality of the printout. Other refillers use a fancy machine that prints out a test strip that checks to make sure all the nozzles are firing properly. Some remanufactures use equipment that test for altitude pressure. If the pressure in a cartridge gets too high during shipment the cartridge will leak. Step 6. Packaging. The cartridges are physically inspected once more. The print heads are professionally taped using a machine that applies tape to the heads with the exact pressure necessary. This is not guess work. Print head sealing tape applied the wrong way may damage the cartridge. The cartridges are then sealed in bags, some remanufactures vacuum seal the bags, others do not. Actually I have not seen any difference in performance using either method. Lastly they are put in pretty boxes and stored in an upright position with the print heads pointing down. This is important because if the cartridges are laid on their sides it's possible that they can loose their prime. This is why so many inkjet cartridges with print heads don't work when they are shipped through the mail. About the AuthorBarry Shultz is the author of Atlascopy News, and President of Atlascopy, Inc. Atlascopy specialized in affordable alternatives to the high cost of printer supplies. Sign up for the Atlascopy Newsletter and get 10% coupons every week in your email. http://atlascopy.com/signup_new.htm http://www.aaarticles.com/article.php?id=3275 | ||||||||||||||||||||
