| ||||||||||||||||||||
![]() | ||||||||||||||||||||
|
||||||||||||||||||||
1. Safety glasses: These prevent dust, debris, wood shavings, shards from fiberglass, etc from getting into the eyes. Safety glasses are one of the most basic pieces of safety equipment that must be used when working with power tools. 2. Protection for the ears: Power tools can generate a lot of noise, which may sound louder in the cloistered environment of a workshop; in order to minimize damage to the ears, it is advisable to wear earplugs. 3. Knowing the right tools for the job: It is important to know the right tools for the job in order to avoid injury to oneself and damage to the materials. To this end, it is advisable to thoroughly read the instruction manuals provided with the equipment and get familiar with the recommended safety precautions. 4. Correct method of using tools: Tools should not be carried by their cords; tools that are not in use should be disconnected; and while handling a tool connected to a power source, fingers should be kept away from the on/off switch. 5. The right clothes: Long hair should be tied and loose clothing should be avoided. Ideally, clothing that covers the entire body should be worn and heavy gloves should be used in order to avoid sharp implements and splinters from hurting the hands. Masks prevent inhalation of harmful minute particles of the material that is being worked upon. Steel-toed work boots and hard hats can also be worn. 6. Tool inspection: Power tools should not be employed in wet environments and should never be dipped in water; they should be checked periodically for exposed wiring, damaged plugs, and loose plug pins. Nicked cords can be taped but if a cut appears to be deep, a cord should be replaced. Tools that are damaged or those that sound and feel different when used should be checked and repaired. 7. Cleanliness in the work area: This should be maintained because accumulated dust particles in the air can ignite with a spark. Of course, flammable liquids should be kept covered and away from the place where power tools are being used. An uncluttered work area also makes it easy to maneuver the power tool; often distractions caused by a tangled cord can result in an accident. 8. Care with particular tools: Miter saws and table saws should be used with a quick-release clamp and a wood push-through, respectively. Extra care should be taken while using nail guns and power belt sanders. 9. Keep tools in place: Power tools should be returned to their cabinets after use to prevent them from being used by an unauthorized and incapable person. 10. Lighting: It is important to use proper lighting while working with power tools, particularly when working An New Innovative Tool for Hanging Drywall Mark Donovan Hanging sheetrock can be back breaking work and almost impossible to do without two people, particularly if hanging sheetrock on the ceiling. Most professional drywall hangers and do-it-yourself homeowners use a drywall jack or a homemade T-bar to hold the drywall in place while they fasten it to the ceilings. However, for the do-it-yourself homeowner renting a drywall jack can be expensive and using a T-bar can take some getting use to. There is now a new alternative. I recently discovered a rather innovative tool for hanging drywall on ceilings and walls. The tool is extremely low cost, simple to use and very effective for holding drywall in place. The drywall tool goes by the name “FREE HANDS”. It is effectively a support tool for hanging sheetrock on ceilings and eliminates the need for a drywall jack or a T-bar. In addition, the device can also be used for hanging sheetrock on walls. Its simplicity is what makes it so unique. The FREE HAND drywall tool simply consists of two small brackets that can be quickly secured into ceiling joists or wall studs prior to hanging the drywall. The drywall installer then simply slides the drywall into the FREE HAND tool to support the weight of the drywall while it is being secured with screws or nails. FREE HAND can also be used on walls, by measuring down from the ceiling 48 inches and securing the FREE HAND tool to a wall stud. The sheetrock can then be slid into place up against the wall studs and then fastened with drywall nails or screws. Though FREE HAND is low tech it is very effective and low cost. The developer and manufacture, Quality Tool, advertise and sell the product on their website. The next time you plan on hanging sheetrock you may want to consider this alternative for holding drywall. It could save you time, money and maybe even a sore neck and back. To learn more about FREE HAND visit http://www.freehand2000.com. http://www.ideamarketers.com/./library/article.cfm?articleid=75741 | ||||||||||||||||||||