| ||||||||||||||||||||
 | ||||||||||||||||||||
|
||||||||||||||||||||
1. Safety glasses: These prevent dust, debris, wood shavings, shards from fiberglass, etc from getting into the eyes. Safety glasses are one of the most basic pieces of safety equipment that must be used when working with power tools. 2. Protection for the ears: Power tools can generate a lot of noise, which may sound louder in the cloistered environment of a workshop; in order to minimize damage to the ears, it is advisable to wear earplugs. 3. Knowing the right tools for the job: It is important to know the right tools for the job in order to avoid injury to oneself and damage to the materials. To this end, it is advisable to thoroughly read the instruction manuals provided with the equipment and get familiar with the recommended safety precautions. 4. Correct method of using tools: Tools should not be carried by their cords; tools that are not in use should be disconnected; and while handling a tool connected to a power source, fingers should be kept away from the on/off switch. 5. The right clothes: Long hair should be tied and loose clothing should be avoided. Ideally, clothing that covers the entire body should be worn and heavy gloves should be used in order to avoid sharp implements and splinters from hurting the hands. Masks prevent inhalation of harmful minute particles of the material that is being worked upon. Steel-toed work boots and hard hats can also be worn. 6. Tool inspection: Power tools should not be employed in wet environments and should never be dipped in water; they should be checked periodically for exposed wiring, damaged plugs, and loose plug pins. Nicked cords can be taped but if a cut appears to be deep, a cord should be replaced. Tools that are damaged or those that sound and feel different when used should be checked and repaired. 7. Cleanliness in the work area: This should be maintained because accumulated dust particles in the air can ignite with a spark. Of course, flammable liquids should be kept covered and away from the place where power tools are being used. An uncluttered work area also makes it easy to maneuver the power tool; often distractions caused by a tangled cord can result in an accident. 8. Care with particular tools: Miter saws and table saws should be used with a quick-release clamp and a wood push-through, respectively. Extra care should be taken while using nail guns and power belt sanders. 9. Keep tools in place: Power tools should be returned to their cabinets after use to prevent them from being used by an unauthorized and incapable person. 10. Lighting: It is important to use proper lighting while working with power tools, particularly when working Fred Riehl has been surfing and working with Brave New World surf shops for 18 years!The Tube Quest Continues at ... www.bravesurf.com Things you will need: 1 Skate board deck 1 sheet skate board deck griptape 2 skateboard trucks 4 skateboard wheels 8 skateboard wheel bearings 2 risers 1 set of mounting hardware 1 philips head screwdriver 1 skate tool 1 metal file 1 sharp razorblade 1. First apply the skate board deck grip tape. By unpeeling the backing and then carefully stick the tape evenly on the top surface of the skate deck. File down the grip tape around the edges of the skateboard, and then carefully use the razorblade to slice off the excess grip tape that hangs over the edges on the skatedeck. 2. Next, attach your skate trucks to your skateboard deck. Use one of the screws from the mounting hardware to poke a hole in the griptape. Then push the mounting hardware from the top of the skatedeck to the bottom. 3. Now slide the risers over the hardware. Next slide your skate trucks on. Make sure that the bushings from the trucks point toward each other or face the center of the board. Tighten the nut with the skate tool until it's flush with the trucks. Warning: Do not over tighten; you can cause the wood to split. 4. Now press the bearings into your wheels using the skate tool. Repeat this for all four wheels. If you do not have a skate tool. You can use your axe on the trucks by placing the bearing on the axel and then pressing the wheel into the bearing, causing the bearing to slip into the wheel. Warning: Be very carefull not to dent or pinch the metal seal around the sides of the bearing. This will ruin the bearings and cause them not to spin! 5. Once the bearings are in place, you can put the on the trucks. Do not over tighten this will crush the bearing causing it not to role. 6. Now the board is ready to skate. You may need to fine tune the trucks to your liking by loosening them or tighten them. The looser the trucks the easier to carve. 7. Once you are done you can always customize your board with some stickers Remember to skate safe and wear your pads when needed. About the AuthorFred Riehl has been surfing and working with Brave New World surf shops for 18 years! http://www.aaarticles.com/article.php?id=21195 | ||||||||||||||||||||
